Engine And Emission Basic Control System

Описание для Engine And Emission Basic Control System

This application informs and explains in detail about the engine control system and also comes with how to fix or solve problems with your car engine.
Precautions for On Board Diagnostic (OBD)
System of Engine
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the driver of a malfunction causing emission deterioration.
CAUTION:
- Be sure to turn the ignition switch OFF and disconnect the negative battery terminal before any repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves, etc. will cause the MIL to light up.
- Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will cause the MIL to light up due to the open circuit. (Be sure the connector is free from water, grease, dirt, bent terminals, etc.)
- Certain systems and components, especially those related to OBD, may use a new style slidelocking type harness connector. For description and how to disconnect, refer to EL section, “Description”, “HARNESS CONNECTOR”.
- Be sure to route and secure the harnesses properly after work. The interference of the harness with a bracket, etc. may cause the MIL to light up due to the short circuit.
- Be sure to erase the unnecessary malfunction information (repairs completed) from the ECM before returning the vehicle to the customer
TROUBLE DIAGNOSIS - INDEX
Engine Fuel & Emission Control System
Wiring Diagrams and Trouble Diagnosis
PREPARATION
ENGINE AND EMISSION CONTROL OVERALL SYSTEM
ENGINE AND EMISSION BASIC CONTROL SYSTEM DESCRIPTION
Multiport Fuel Injection (MFI) System
Electronic Ignition (EI) System
Air Conditioning Cut Control
Fuel Cut Control (at no load & high engine speed)
Evaporative Emission System
Positive Crankcase Ventilation
BASIC SERVICE PROCEDURE
Fuel Pressure Release
Fuel Pressure Check
Fuel Pressure Regulator Check
How to Check Idle Speed and Ignition Timing
Idle Air Volume Learning
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
TROUBLE DIAGNOSIS - INTRODUCTION
TROUBLE DIAGNOSIS - BASIC INSPECTION
TROUBLE DIAGNOSIS – GENERAL DESCRIPTION
TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT
TROUBLE DIAGNOSIS FOR POWER SUPPLY
DTC P0100 MASS AIR FLOW SENSOR (MAFS)
DTC P0115 ENGINE COOLANT TEMPERATURE SENSOR (ECTS) (CIRCUIT)
DTC P0120 THROTTLE POSITION SENSOR
DTC P0130 (RIGHT, -B1), P0150 (LEFT, -B2) FRONT HO2S (CIRCUIT)
DTC P0325 KNOCK SENSOR (KS)
DTC P0340 CAMSHAFT POSITION SENSOR (CMPS) (PHASE)
DTC P0605 ECM
DTC P1217 ENGINE OVER TEMPERATURE (OVERHEAT)
DTC P1335 CRANKSHAFT POSITION SENSOR (CKPS) (REF)
DTC P1336 CRANKSHAFT POSITION SENSOR (CKPS) (POS) (COG)
ABSOLUTE PRESSURE SENSOR
INTAKE AIR TEMPERATURE SENSOR
FRONT HEATED OXYGEN SENSOR HEATER
REAR HEATED OXYGEN SENSOR
REAR HEATED OXYGEN SENSOR
FUEL TANK TEMPERATURE SENSOR
CRANKSHAFT POSITION SENSOR (CKPS) (POS)
EGR VOLUME CONTROL SYSTEM
EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
VEHICLE SPEED SENSOR (VSS)
IDLE AIR CONTROL VALVE (IACV) – AUXILIARY AIR CONTROL (AAC) VALVE
CLOSED THROTTLE POSITION SWITCH
A/T COMMUNICATION LINE
SWIRL CONTROL VALVE CONTROL SOLENOID VALVE
IGNITION SIGNAL
A/T DIAGNOSIS COMMUNICATION LINE
PARK/NEUTRAL POSITION (PNP) SWITCH
VARIABLE INDUCTION AIR CONTROL SYSTEM (VIAS)
INJECTOR
START SIGNAL
FUEL PUMP
ELECTRONIC CONTROLLED ENGINE MOUNT
POWER STEERING OIL PRESSURE SWITCH
REFRIGERANT PRESSURE SENSOR
ELECTRICAL LOAD SIGNAL
MIL & DATA LINK CONNECTORS
SERVICE DATA AND SPECIFICATIONS (SDS)
Fuel Pressure Regulator
Idle Speed and Ignition Timing
Mass Air Flow Sensor
EGR Temperature Sensor
IACV-AAC Valve
Resistor
Throttle Position Sensor
Calculated Load Value
Intake Air Temperature Sensor
Rear Heated Oxygen Sensor Heater
Crankshaft Position Sensor (REF)
Fuel Tank Temperature Sensor
Camshaft Position Sensor (PHASE)
Give your assessment, is this application useful?
if useful provide the best judgment for this app
thank you
This application do not need internet connection (can be used offline) Free download